• <button id="66kmq"><dl id="66kmq"></dl></button>
    <table id="66kmq"></table>
  • <li id="66kmq"></li>
  • <code id="66kmq"></code>
  • <code id="66kmq"></code>
    歡迎來Nano電子商城!
    您好 [請登錄]   [免費注冊]
    x
    全部商品分類

    SKC 44XR通用采樣泵原版操作手冊

    下載次數:313 瀏覽次數:557發布時間:2017-12-16 16:38
    允許查看的會員等級:非會員   普通會員   高級會員   VIP會員   

    文檔詳情

    ? Protect sample pump from weather when in use outdoors.

    ? Powering the pump with any device other than the approved battery pack voids the UL Listing for intrinsic

    safety.

    ? Do not use the pump with the Battery Eliminator in hazardous locations. UL Listing for intrinsic safety is not in

    effect during pump operation with Battery Eliminator.

    ? Use of any device other than the approved battery pack or Battery Eliminator to power the pump voids any

    warranty.

    ? Charge pump battery completely before calibration and sampling.

    1. Replace the sampling medium used for calibration with an unexposed medium for sample collection.

    2. Place the sampling medium where appropriate for sampling.

    a. For personal sampling, clip the sampling medium to the worker in the breathing zone.

    b. When using impingers, an in-line trap (SKC Cat. No. 225-22 or 225-22-01) is required to prevent

    fumes from accidentally being drawn into the sampler. Place the in-line trap between the pump

    and the impinger. Mount the impinger and trap to the face of the sampler using the accessory

    mounting screws (Figure 1) or place them in a holster at the worker’s waist.

     Failure to use an appropriate in-line trap during impinger sampling voids any warranty.

    c. When using the pump for pressure applications, such as bag sampling, thread the exhaust port

    fitt ing supplied with the pump into the air discharge port on top of the pump; hand-tighten only.

    Using PTFE tubing, connect the inlet of the sample medium (e.g., sample bag) to the exhaust port

    fitt ing on the pump. Turn on the pump to collect the appropriate volume of air. Shut off the pump

    and close inlet on sample medium to stop sampling.

    3. Start sampling by turning on the pump using the on/off switch (Figure 1). Record the start time.

    4. At the end of the sampling period, turn off the pump and record the stop time.

    5. Seal the sample and send it with blanks and pertinent sampling information to a laboratory for analysis.

    6. Verify the fl ow.

    a. Turn on the pump and reinstate the calibration train and sampling media.

    b. Take three readings and record the average value as the post-sample fl ow rate. Do not adjust the pump fl ow rate during this step.

    c. Compare the pre and post-sample fl ow rates. Note in sampling documentation if the values diff er by more than ± 5%


    我們營業的時間9:00-18:00

    • 技術
    關閉在線客服

    Nano電子商城微信公眾號手機商城 Nano電子商城微信公眾號二維碼

    手機商城           微信商城

    任何購物問題請聯系納米科技(香港)有限公司  | 江蘇省蘇州市昆山開發區章基路189號科創基地2號樓202室 Tel:021-52069907 email: 19mro@19mro.com

    工作時間:周一至周五 8:00-18:00; 網站備案號 :滬ICP備12049383號; Copyright?2009-2012 19mro.com 版權所有 


     
    日日摸日日踫夜夜爽无码| 最近中文字幕完整版免费高清| 最近免费中文字幕高清大全| 人妻少妇伦在线无码专区视频| 最好看更新中文字幕| 日韩乱码人妻无码中文字幕视频| 在线精品无码字幕无码AV| 中文字幕免费在线| 亚洲高清无码综合性爱视频| 无码精品视频一区二区三区| 毛片免费全部播放无码| 中文字幕日本高清| 色婷婷综合久久久中文字幕| 亚洲&#228;v永久无码精品天堂久久 | 无码精品久久久久久人妻中字| 日韩乱码人妻无码中文视频| 中文字幕aⅴ人妻一区二区 | av一区二区人妻无码| 亚洲AV无码乱码在线观看裸奔| 日韩av无码免费播放| 一本大道香蕉中文日本不卡高清二区 | 久久精品aⅴ无码中文字字幕不卡| 成在人线av无码免费高潮水| 亚洲AV永久无码区成人网站| 免费无码H肉动漫在线观看麻豆| 中文字幕国产| 精品亚洲AV无码一区二区三区| 中文字幕在线无码一区| 免费无码一区二区三区蜜桃| 久久久无码精品亚洲日韩蜜臀浪潮| 日韩中文久久| 69堂人成无码免费视频果冻传媒| 中文字幕av日韩精品一区二区| 中文字幕性| 亚洲成a人片在线观看无码专区| 无码乱人伦一区二区亚洲| 久久久久亚洲av无码专区喷水| 国产无遮挡无码视频免费软件| 国精品无码一区二区三区左线| 97久久精品无码一区二区天美| 岛国av无码免费无禁网|