• <button id="66kmq"><dl id="66kmq"></dl></button>
    <table id="66kmq"></table>
  • <li id="66kmq"></li>
  • <code id="66kmq"></code>
  • <code id="66kmq"></code>
    歡迎來Nano電子商城!
    您好 [請登錄]   [免費注冊]
    x
    全部商品分類

    LMS粉塵氣溶膠發生器原版使用手冊

    Weigh out and apply ASHRAE 52.1 dust in the tray and distribute the dust in a thin, evenly-spread la
    下載次數:344 瀏覽次數:597發布時間:2018-07-01 17:16
    允許查看的會員等級:非會員   普通會員   高級會員   VIP會員   

    文檔詳情

    - Unpack the dust feeder.

    - Plug in the electrical line to standard 220-240 VAC outlet.

    - Note that the feeder tray slides freely on two nylon rails when the vertical lever pin is disengaged (lifted up) from the feeding chain.

    - Set the tray in position by inserting (push down) vertical lever pin between two links on the feeding chain at approx. 3 inch or more forward of the sprocket that turns the chain.

    - Since the dust will be spread evenly across the width of the tray, and the tray advances ~28 cm (~11”) in 10 minutes, it is necessary to mark on the tray where the dust will be placed; make a mark on one edge of the tray that rides on a nylon bar near the paddle wheel – designate this as the starting point (0) for dust placement. Turn on the tray feed toggle, allow 10 minutes for the tray to advance, then mark the tray again – about 28 cm back from the staring point - designate this as the stopping point (10) for dust placement.

    - Supply an air pressure line (720 Kpa max) to the air inlet fitting (1/4 FPT) located on the side of the unit.   Option: it may be desirable to connect a standard shut-off valve and/or a quick-disconnect fitting(s) at this air inlet for convenience.  

    - Dry-run the unit without dust on tray to check unit operation:  with electricity & 700 Kpa at air inlet, turn on toggle switches first for TRAY FEED, then PADDLE WHEEL, then ASPIRATOR, and ascertain that tray moves slowly, paddle wheel rotates with wheel guard down, and that forced air comes out of the delivery tube.  

    OPERATION

    - Set the line pressure to 600 Kpa (for ASHRAE usage the airflow is 14.5 scfm and pressure should be set accordingly to achieve this flow rate). Refer to section 5.4 in the ASHRAE 52.1 procedures.

    - Connect the air outlet of the delivery tube to your test air duct. 

    - Weigh out and apply ASHRAE 52.1 dust in the tray and distribute the dust in a thin, evenly-spread layer between the two start/stop marks (0 and 10 min.) on the tray.  Depending on the flow rate of the filter under test, the amount of dust needed equates to 2 grams of dust per 1000 cfm of air flow in the duct per minute of dust feed.

    ?

    我們營業的時間9:00-18:00

    • 技術
    關閉在線客服

    Nano電子商城微信公眾號手機商城 Nano電子商城微信公眾號二維碼

    手機商城           微信商城

    任何購物問題請聯系納米科技(香港)有限公司  | 江蘇省蘇州市昆山開發區章基路189號科創基地2號樓202室 Tel:021-52069907 email: 19mro@19mro.com

    工作時間:周一至周五 8:00-18:00; 網站備案號 :滬ICP備12049383號; Copyright?2009-2012 19mro.com 版權所有 


     
    久久超乳爆乳中文字幕| 日韩精品人妻一区二区中文八零| 亚洲AV无码乱码在线观看裸奔| 精品久久久久久无码免费| 一本色道无码道DVD在线观看| 丰满熟妇乱又伦在线无码视频| 日本中文字幕在线视频一区| 高清无码中文字幕在线观看视频 | 亚洲日韩中文在线精品第一| 寂寞少妇做spa按摩无码| 下载天堂国产AV成人无码精品网站| 亚洲ⅴ国产v天堂a无码二区| 中文字幕精品无码久久久久久3D日动漫 | 无码 免费 国产在线观看91| 无码AV波多野结衣久久| 亚洲精品成人无码中文毛片不卡| 国产精品综合专区中文字幕免费播放| 亚洲一级特黄大片无码毛片| 国产AV无码专区亚洲AV男同| 日韩精品无码久久久久久| 中文字幕有码无码AV| 无码国产精品一区二区免费 | 免费无码又爽又黄又刺激网站 | 久久男人Av资源网站无码软件| 免费A级毛片无码A∨免费| 亚洲中文无韩国r级电影| 亚洲一级特黄无码片| 久本草在线中文字幕亚洲欧美| 特级小箩利无码毛片| 无码人妻少妇伦在线电影| 久久精品?ⅴ无码中文字幕| 国产成人精品无码播放| 国产精品VA在线观看无码不卡| 国产精品多人p群无码| 精品久久久久久无码人妻热| 久久久久无码精品| 亚洲毛片av日韩av无码| 日韩精品久久无码人妻中文字幕| 人妻丰满av无码中文字幕| 久久久网中文字幕| 无码乱码av天堂一区二区|